Best Automotive Replacement Axle Shafts
1 USA Standard Gear (SL C8.25-27) Spartan Locker for Chrysler 8.25" differential with 27 spline axles
Designed for off-road usage, this lunchbox locker is easy to install and provides a significant increase in strength over stock differentials. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"If you decide to go this route it’s a budget locker it works well install is about 3-4 hrs taking your time ."
"Great product shipped amazingly fast."
"The 4cyl version of this I use and works quite well in the front-end."
"Takes a few days to break in; as the first few days the locker would bind up the axle and make a loud pop, but that pretty much went away except for the occasional time I'm turning hard into a parking space or something similar."
"Great locker for the price and self install, you have to know a little what your doing though, I’d say took about 2 hours to install in my jeep TJ Dana 44."
"Increases traction wonderfully."
"Showed up ahead of the scheduled day."
"Clicks and pops louder than I expected."
Brand New Driveshaft Assembly With New Service-able U-Joints. Fits 1997-2001 Honda CR-V All Wheel Drive (AWD/4WD). Replaces 40100-S10-003, 40100-S10-A01. This is a complete brand new driveshaft assembly with remove-able universal joints. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Good OE fit."
"Who ever designed a drive shaft where you cannot replace the u joints is a moron."
Brand New 4WD Front Differential Axle Disconnect Assembly With 4WD Actuator. Axle Disconnect Is Also Called Intermediate Shaft Bearing Assembly. Upgraded Design Uses Synthetic Grease For Long Trouble Free Life. Fits 2002-2009 Chevrolet Trailblazer 4WD (Except AWD). Fits 2002-2009 GMC Envoy 4WD (Except AWD). Fits 2003-2008 Isuzu Ascender 4WD (Except AWD). Fits 2002-2004 Olds Bravada (Except AWD). For AWD (All-Wheel Drive) Models See APDTY 711227. If you need the intermediate axle shaft, See APDTY 112658. Replaces GM Part #: 15884292 & 12471631, 12479081, 12471629, 12471631, 12471627, 12471624, 12479132, 12479302. Made 100% In The USA. Upgraded With Synthetic Grease For Long Trouble Free Bearing Life.
Reviews
Find Best Price at Amazon"My 07 trailblazer that I recently bought had a grinding noise all the time and was told it was the bearings and I trusted them but later found out the 4x4 wouldn't engage."
"The front axel disconnect fit perfectly and was a direct replacement for the original one."
"Perfect fit."
"Works as advertised."
"Works beautifully satisfied customer."
"Perfect replacement and great price."
"The part I got from amazon work grate and the four wheel drive works know."
"Because of this issue I no longer have a 4x4 vehicle, I am outside the return window and I'm surely not buying another one from this seller."
Best Automotive Replacement Axle U-Bolt Kits
These square u bolts are engineered to clamp 2.5 inch wide leaf springs and are 12 inch extra-long measured from the bottom of the bend to the bottom of the threads. Contents: 4 certified carbon steel square leaf spring axle U-bolts with grade 8 hi-nuts and extra thick washers, clear zinc plated rust protection.
Reviews
Find Best Price at Amazon"I replaced my factory 2003 Z71 leaf springs with 3 leafs, with HD, 5 leaf springs."
"Exactly what I needed, was installing rear add a leafs on my 94 Chevy half ton and I discovered the factory u bolts were nearly worn throug."
"Good quality, only issue is mine were .5" to short from the 12.5" described making them to short for my application."
"I installed a seven-leaf spring set on my GMC Sierra p/u in place of the factory three-leaf springs to boost my trailering capacity."
"Purchased these extended U bolts for my 03 silverado when I added a leaf to the rear spring pack."
"Well they wont work on one inch blocks."
"They are actually thicker than oem and come with Grade 8 hardware."
"At first glance the blocks had a crappy powder coating and the u bolts and nuts had metal chips embedded in the threads that I couldn't even blow out with a compressor. Upon trying to install the blocks and reassemble, I noticed my u bolts were bending outward to the point of not being able to fit into the saddle."
Best Automotive Replacement Axle Spindle Nut Retainers
1/4" (6.4mm) hole size; panel range: .095"-.540" - Nylon Shield Retainers --Qty: 20. 9/32" (7.1mm) hole size; panel range: .125"-.310" - Nylon Shield Retainers -- Qty: 20. 5/16" (7.8mm) hole size; panel range: .078"-.490" -Black Shield Retainers --Qty: 20. 23/64" (9mm) hole size; panel range: .060"-.510" - Black Shield Retainers --Qty: 20. 3/8" (9.5mm) hole size; panel range: .115"-.565" -Black Shield Retainers --Qty: 20. 25/64" (10mm) hole size; panel range: .040"-.787" -Black Shield Retainers --Qty: 20. Push Type Retainer Kit came with a nice plastic box for easier to pick a type of retainer that you want to use.
Reviews
Find Best Price at Amazon"-Good for doing small repairs/replacements on various cars. - price is decent for the quality:quantity raito. CONS. - not great for a bigger repair/replacement project due to limit of 20pc each. TL;DR. Great price, solid quality, decent count (20ea),has just about every type of retainer for the common use."
"It’s no longer nuts and bolts when it comes to cars."
"Looks good should have what looks like the most popular fasteners that are used."
"This kit is great to have on hand to replace the pins you lose or break."
"This assortment looks like it has a good selection of retainers, have not used any yet so it is hard to say how they will work but the quality looks very good."
"no fillers only useful parts."
"has every size I need, stay in place when installed."
"Not exactly the highest quality, however there are a lot of them in this kit, and are a fraction of the cost of the "help" area of the auto parts store."