Best Automotive Replacement Carburetor Spacers & Adapters
The Edelbrock Four-Hole Square-Bore to Spread-Bore Carburetor Adapter allows proper installation of carburetor to manifold. Mounts Edelbrock square-bore carburetors to stock Quadrajet and Thermo-Quad manifolds.
Reviews
Find Best Price at Amazon"Bought this because another website said you can also use this to mount a spread bore (Quadrajet) to a square bore intake."
"The gaskets sealed well, but if you're planning to install this exactly as I did, you'll want to pair it up with the ICT Billet heat riser choke blockoff plate, and possibly an EGR delete blockoff plate."
"The product was fine, but the thread holes were drilled a bit "crooked.""
"As it was, I used the vacuum port on the back of the Edelbrock carb to hook my power brakes up, just like the original QuadraJet."
"I bought this adapter to fit the reverse from its intention - a spread-bore carburetor onto a square-bore intake."
"Edelbrock is a very good name and the quality is good even though it's made in China."
"Works perfectly as an adapter from square bore carb/throttle body to spread bore intake."
"Didn't work for my application, but looked to be excellent Edelbrock quality."
The Edelbrock 4-Barrel Phenolic Carburetor Spacers are used where more plenum volume or more carburetor-to-plenum floor distance is required. Enhances low-RPM torque, throttle response and dampens reversion effects on the carburetor.
Reviews
Find Best Price at Amazon"It looks to be OK and should fit, BUT I cannot mount it yet because it did not come with the studs that are shown with the spacer."
"Works great provided low-end torque."
"Came with everything pictured, not sure why others didn't get the studs?"
"Very nice."
"Worked perfect and corrected my carburetor from overheating."
They adapt any 4-bolt, 4-barrel to any small 4-bolt, 2-barrel manifold and / or 4-bolt, 2-barrel to any 4-bolt, 4-barrel manifold. Open center adapter measuring 1" thick (without gasket).
Reviews
Find Best Price at Amazon"The problem is, the allen set bolts that are supplied to sit lower to clear the throttle butterflies are not suited to actually holding the bracket down. I then used normal bolts with a 7/8"ish wide washer that fit in the holes so I could use a much smaller gasket on top."
"I used my stock carb mount bolts with my own washers to mount the adapter to the manifold, then the silver bolts to mount carb to adapter."
"Great quality, but I returned it because it wouldn't work for my application."
"It's exactly as advertised."
"When the product arrived a Rochester 2 barrel throttle linkage would not clear."
"I was using the 2 barrel carburetor on a 4 barrel intake."
"I really didn't like the way the mounting holes were designed."
"This also puts your 2bbl carburetor farther rearward than the 4bbl so you will need to do some creative work with the throttle cable and air filter."
Best Automotive Replacement Carburetor Caps
Dorman offers a comprehensive line of Vacuum Caps for almost any automotive repair job. Excellent for capping lines and hoses while testing carburetors, emission control systems, vacuum lines, and more.
Reviews
Find Best Price at Amazon"I have to give this three stars because the seller didn't state the sizes of the caps and therefore the biggest one was too small for my need."
"Replacing your caps with new will improve your engines performance and idle stability over leaky caps."
"I bought these for my truetone 1spot 9v power adapter daisy chain to cover the extra connectors so they wouldn't short out if they hit a mic stand or the inside of my metal pedal board, the little blue ones are a bit long but work like a dream when you cut them shorter."
"Got these to cover my sprinkler valves since who knows what happened to the old ones."
"Nice quality, very pleased!"
"Used the red plugs on my Toyota, I am sure I will find a use for the others in time."
"Items as described."
"Holding up better than the rubber ones I had, cheaper than in store."
Best Automotive Replacement Carburetor Floats
Carburetor / Tecumseh 640084B Pack Size:1 TECUMSEH 640084B, TECUMSEH 640084A, TECUMSEH 640084, TECUMSEH 632107, TECUMSEH 632107A GREEN LINE 13141, OREGON 50-640, OREGON 49-242, ROTARY 13141 TECUMSEH HSK40, HSK50, HSSK40, HSSK50, HS50, LH195SA Gasket NOT included , Not for Go-Kart applications , Not compatible with greater than 10% ethanol fuel. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"The time it'd have taken to rebuild or have someone else rebuild the original isn't even worth it. The only negative I can come up with is the spring for the choke detente was perfectly vertical and when I attached my choke lever, it would've engage on the fully closed choke detente, to fix this I simply took a screw driver and forced the spring over a tiny bit, enough to loosen up the tension...and wala!"
"I took the old carb off and put this one on."
"This was almost too easy, there re no more adjustments (factory sealed), primed it 5-6 times and it fired right off, running smoothly."
"A better cheaper way to fix my snowblower than trying to have the original carb rebuilt."
"time Rita was a direct fit worked perfectly amazing price I would recommend this to anybody."
"Awesome carburetor!"
"BTW.... My old one had an adjustable main jet, this one is a fixed jet."
"I was very hesitant at this price but the machine runs perfectly."
Best Automotive Replacement Carburetor Service Tools
The Pro-Synchronizer will not restrict airflow and feature an easy to read 1-30 kg/h numbered scale for precise synchronization. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"This item should have more information about whether or not adapters would be required."
"I hate having to go on line and look at videos as people use it differently."
"Works great simple tool to use. An inexpensive and must have tool for the money, recommend to all (D I Y selfers) & mechanics!"
"You will need to remove any air filter connectors or baffles so the unit will have direct access to the carbs for most accurate readings."
"I use this for my 65 bug and it works great."
"The Pro-Sync worked great to sync my Weber 34 ICT dual carbs."
"The adaptor that comes with this device fits neatly inside the throat of a Carter or Stromberg two barrel carb."
"This works perfectly to sync my multiple carbs on my hot rod VW."
Best Automotive Replacement Carburetor Return Springs
The Edelbrock Carburetor Step-Up Spring Kit contains one of each 3 Hg (blue), 4 Hg (yellow), 5 Hg (orange), 7 Hg (pink) and 8 Hg (plain) springs. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Factory 1406 comes with YELLOW springs."
"I had a nasty flat spot on my 1972 c20."
"I used the heavy set of springs,cured my stumble at lite throttle at 2000rpm.No more lean miss."
"They do make a small difference but the carburator itself isn't so great."
"I recently added an Air/Fuel Ratio gauge to my Street Rod and these are just what I need to get my carbs dialed in perfectly!"
"Problem solver."
Best Automotive Replacement Carburetor Diaphragms
Magnafuel MP-9400-03 MP-9433 DIAPHRAM.
Reviews
Find Best Price at Amazon"Saved our 12 Cylinder BMW , we used this to replace the broken (torn) diaphragm in the hpfp's."
"Everything good shipping came in as date stated very happy."
Best Automotive Replacement Carburetor Rebuild Kits
This is a Replacement Carburetor for Tecumseh 640350, 640303, 640271. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"After cleaning the carb, and reassembling (with a sketchy looking bowl gasket), I noticed that this hadn't helped my 'starting' problem and instead made it worse; I now had a small gas leak out of the carb bowl. I used the following items: Carburetor MaxPower 13566 Carburetor for Tecumseh 640350, 640303 and 640271. Ignition Coil NEW TECUMSEH 34443 34443A 34443B 34443C 34443D IGNITION COIL SOLID STATE MODULE. Air Filter Oregon 30-031 Paper Air Filter Tecumseh Replacement Part 36905 2-3/4-inches by 1-3/4-inches by 2-7/8-inches. Fuel Line Hose Clamp Stens 120-251 Hose Clamps."
"These are excellent generic carburetors that fit perfectly on a Tecumseh engine used to power a common Toro Recycler GTS. A couple hints when changing these carburetors on a Toro GTS: - Fully remove the muffler connected with two bolts. Governor adjustment is easy and is typically misaligned due to the delicate spring becoming damaged or stretched during carburetor removal."
"I took way more than 20 minutes (more like 3 hours) but that's only because I didn't know what I was doing and had to carefully analyze everything, plus make a couple trips out to the store to replace the fuel line while I was doing this. I don't know enough to blame the carburetor for it, although that could be it... it could also be the mower is 16 years old."
"Simple install: remove muffler, remove old carb with intake manifold and linkage, remove fuel line and vent from old carb, separate old carb from intake manifold, transfer intake to new carb, transfer the air cleaner plate and re-install the new carb in reverse order of removal."
"Easy replacement (clean the engine well around this area before starting)."
"This was a replacement carb for the original factory installed carb on my Toro lawn mower that got a terminal case of the "leaks"."
Best Automotive Replacement Carburetor Accelerator Pumps
It features a manual choke, center hung float bowl, universal throttle lever, all-metal parts, and replaceable jets. Power valve blow-out protection adds trouble free operation.
Reviews
Find Best Price at Amazon"Was not the right part however easy return so I will recommend these guys."
"Put it on started right up."
"Had to rebuild because it was leaking gas at the base of the carb."
Best Automotive Replacement Carburetor Power Valves & Gaskets
For Fitment: Year Make Model Submodel. 1994-1995 BMW 530i. 1994-1995 BMW 540i. 1997-2003 BMW 540i. 1993-1995 BMW 740i. 1997-2001 BMW 740i. 1993-2001 BMW 740iL. 1994-1997 BMW 840Ci. 2000 BMW X5. 2001-2003 BMW X5 4.4i. 2002-2003 BMW X5 4.6is. 2003 BMW Z8 Alpina. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"So far I've only used the front spacer to intake gasket, but it fit perfectly and fixed the leak that was causing my 740iL to run lean and stumble."
Best Automotive Replacement Carburetor Governor Diaphragms
FORKLIFT DIAPHRAGM KIT 04221-U2010-71. Pressure and Computer tested for consistent Quality and unsurpassed reliability.
Find Best Price at AmazonBest Automotive Replacement Carburetor Hot Idle Compensators
It offers enthusiasts a straight-forward carburetor designed to deliver a stable idle, amazingly crisp throttle response and smooth performance. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"I wired it to kick on when AC Compressor comes on."
"Prefect fit and works great."
Best Automotive Replacement Carburetor Decel Valve Diaphragms
CFM Performance Focus ST symposer delete with pressure port. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"Got here a little late but it was worth the wait - quality product and the interior is just a little quieter."
"Only 2 gripes is I wish it came with the paste or tape to put on the threads of the plug or valve."
"Easy to install, and did what it was supposed to."
"Awesome product, Well made and I like having the option of adding a vacuum port down the line if I go big turbo and want a different BOV or boost gauge."
"Item was EXACTLY as advertised and was shipped very quickly."
"it quieted the cabin down i can hear a little more of the turbo and has an option for if i want to add a boost gauge or vacuum gauge."
"Ordered and it the simplest mod ever."
"Works great, bolts right up."
Best Automotive Replacement Carburetor Throttle Ball Joints
Description: Fits Chevy, Ford & Mopar When Using A Holley 4150 Or 4160 Series Carb. Note: Will Not Work On 4500 Dominator Series Carbs. All Hardware And Brackets Included As Pictured. For Use With Many Different Kinds of Throttle Cables (Including Aftermarket Cable) Which We Have Available In Our Ebay Store Use With All Original And Aftermarket Applications. Fits 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 Engines When Using A 4150 / 4160 Series Holley Carb. Fits Chevy, Ford & Mopar When Using A Holley 4150 Or 4160 Series Carbs.
Reviews
Find Best Price at Amazon"The only complaint I have is the front portion of the bracket will require the coil to be relocated on an FE Ford motor."
"Looks nice, needed to modify 1 of the 2 adapters to fit the stock Ford throttle cable."
"Works good on my moter for the carburetor."
"The throttle cable bracket is a good one."
"Pretty cool product could be packaged better but overall good product."
"Excellent piece works beautifully."
Best Automotive Replacement Carburetor Air Bleed Valve O-Rings
12/Pk.
Reviews
Find Best Price at Amazon"Once I received the proper size, these O-rings performed like the originals..."
"Item was delivered on time but was not the size I needed."
"Not the right size but my fault not their's."
"Happy with service."
"perfect fit love them easy to install."
Best Automotive Replacement Electric Choke Conversion Kits
This five-foot cable choke conversion kit from Help comes with a black knob and includes everything needed to install. Kit includes manual choke cable and everything needed for installation.
Reviews
Find Best Price at Amazon"When I dropped the small lock washers and nuts, I was able to retrieve it within the valleys of the engine block with the magnetic screwdriver."
"Not heavy enough to open choke after closing it."
"GREAT PRODUCT FAST DELIVERY."
"All parts nessasary for easy installation were there ."
"I am a mechanic and will not use this kit again if another is available with a heaver cable."
"You get what you pay for."
"I ordered this kit and the package was opended inside the delivery box."
Best Automotive Replacement Electric Assist Choke Controls
The Edelbrock Performer 600 CFM Vacuum Secondary Electric Choke Remanufactured Carburetors are completely disassembled, inspected and thoroughly cleaned before reassembly for maximum fuel economy. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"I ended up buying an AEM Wideband A/F guage and tuned the carb to Idle at 14.7, Cruise at 14-15, and WOT 12.5-13.5."
"did not have dvd that comes with carb."
"it was missing parts gaskets electric choke wiring carb plugs I am not happy."
"Had no problems."
"I only had 50 miles on the carb before it stopped being safe to drive."
"Replaced carb with another Edelbrock 600 CFM that was on another running vehicle and the fuel pressure regulator works fine."
"I was getting gas to the carb but not thru the carb. I did not run truck long enough to have it look like this and the gas I am using I bought that day and checked to see from leftover in the can and it is clean good gas... At this point I am very disapointed..."
"As soon as I got it the electric choke went out, its a pain in the butt to keep tuned, runs too rich or too lean and hard to find a happy spot I can leave it for even a week but I have to keep changing it almost daily."