Best Mechanical Vibration Damping Mounts
The static load rating of these feet is limited due to the acceptable load rating of the stud (tensile strength 500/mm2).
Reviews
Find Best Price at Amazon"The foot swivels slightly to adjust for uneven floors."
"Worked great for my laundry tub legs to balance them on an uneven floor!"
"Excellent leveling feet!"
"Excellent quality, stainless steel, easy to adjust height."
"Works exactly as advertised and holds my workbench quite well."
"Works as expected."
"Well made."
GN 351.1 / GN 351.2 / GN 351.3 vibration isolation mounts, also known as vibration mounts, anti-vibration mounts, vibration bobbins or rubber bumpers, are suitable for the elastic mounting of machine units such as motors, compressors and pumps.
Reviews
Find Best Price at Amazon"Feet work really well."
"I used them as a replacement for an exhaust mount on a snowmobile, which cost 80 a piece from the factory."
"good product, good customer service."
"Product as described and very speedy shipment."
"It was what it was suppose to be."
Engineered for easy use, simply mount the large, stationary compressor to the floor with the Powermate Vx Vibration Isolator for minimized reverberation. Powemate vibration isolators curb the noise and vibration produced by large stationary compressors.
Reviews
Find Best Price at Amazon"I put these under the 4 feet of my 80gal, compressor."
"These worked great holding up my 80 gallon IR dual stage compressor."
"Nice size to fit the feet of my air compressor."
"I needed these to place under an air compressor.This is a great product and works as intended, but It was a little pricier than I would have expected."
"Before adding these, my 60 gallon air compressor vibrated the concrete floor in the entire garage."
"Really quiets the compressor floor mounts."
"Used them under the feet of my air compressor when I mounted it to the concrete floor in my shop."
Best Mechanical Vibration Damping Pads
Size: 1-Pack. Item features easy to install reduce maintenance costs reduce noise.
Reviews
Find Best Price at Amazon"Life Hack: if you don't have easy access to the back of the washer, you will at first wonder how to put these in position below the rear "feet" of the washer."
"The washing machine sounded like a jet engine and could be heard throughout the house during the spin cycle."
"Seems to reduce vibration."
"These really really work good they help balance out the washer and it’s not sliding around the floor."
"it does stop the wash machine walking."
"Our washer kept slipping forward on our hardwood floors."
"As long as the load is light and the machine is properly level, there is little to no vibration on the highest spin cycle. Occasionally, when a heavy load is imbalanced, the machine will vibrate and "walk"."
"These might work well for a lightweight appliance, however for a heavy front loading machine they get smashed down to a flat pancake like shape and ruined."
Best Mechanical Vibration Damping Clamps
Widely used for mechanical equipment, instrument and apparatus, food and pharmaceutical industry equipment.
Find Best Price at AmazonBest Mechanical Vibration Damping Compounds
Acoustic Blanket, 1" Thick wall/ceiling Panels, 4' x 6'. Lightweight easy to handle material is an excellent noise absorber.
Find Best Price at AmazonBest Mechanical Vibration Sensors
Reviews
Find Best Price at Amazon"Turns out the main board was at fault and needed to be replaced."
"I pulled the control circuit board and saw that the motor relay switch had burned up one of its solder joints on the board."
"This component was just what I needed to get my shorted out control board for my Whirlpool Duet dryer up and running again saving my a small fortune vs replacing the entire board."
"Less than $5 component or over $500 to replace the appliance."
"The shipment or package poor legs bent due to not set in foam hope not to break when bending back in place."
"Replaced a relay on the board in my washing machine with this."
"Had a bad relay and blown track on board."
"I used this on my maytag drier and worked perfectly,very nice quality."
Best Mechanical Shock Absorbers
Protects Accugage head from damage.Fits all Accugages. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"My Accugage is a solid, dependable part of my motorcycle maintenance routine and it was time it received a little protection of its own."
"To fix I wrapped the gauge in a flat piece of rubber (old garage door seal, cut to size) which I attached with two sided tape and then put this cover on."
"I installed this on an older M series gauge and it seems like it will protect it well enough."
"My favorite nitrogen regulator gauges broke when my nitrogen tank fell over."
"I dropped that one enough to know that for my purposes, some form of protective covering like this would be mandatory for my new gauge. TIP: If you have difficulty fitting the cover over your gauge, I suggest placing the rubber cover into a very hot cup of water for a few minutes, and then installing it."
"Great addition to my Meiser Presta-valve dial gauge for low pressures!"
"It's not really an issue, but a bit of self-adhering tape (or friction tape) around the edge of the gauge tidied up the fit."
"Fits my Low Pressure Gauge [SX Series Accugage Low Pressure Tire Pressure]. and will protect it from dropping damage... a perfect add on to gauge ..."