Best Automotive Replacement Exhaust Manifolds
Easily repair exhaust leaks without removing broken manifold bolts with Dorman's Exhaust Manifold to Cylinder Head Repair Clamp. Eliminates the need to remove cylinder head, saving you time and money.
Reviews
Find Best Price at Amazon"Read the many reviews and decided it was time to order as I was tired of exhaust noise on start up. Removed it with ratcheting wrench and then installed the bottom bolt to hold bracket in place."
"One final thought I have is install this whether there is a broken bolt or not as it will insure it won't break, basically it is reinforcing a common problem."
"Only works to eliminate exhasut leak ticks when the manifold bolt has been broken in the position mounted - doesn't address the many other causes of GM V8 ticks (carbon, lifters, etc)."
"Good luck getting a torque wrench in there. What I did was put my torque wrench in the vice, put my regular wrench up to it, and pushed at the same distance up the torque wrench handle as the regular wrench went. That allowed me to get a feel for how hard I needed to push on the regular wrench when tightening the bolts. It wasn't exact, but there was no way I could get a torque wrench up there."
"It does require some patience though, I worked from the top, bottom and removed the inter fender to get it installed.I thought it would be a 20 minute job but ended up taking close to 2 hour because there is not much room and my fingers are too big for the limited space between the engine and the firewall."
"The outer threads are stripped and the bolt sheared almost flat and is still buried in the head so removing the remainder of the bolt and installing a Helicoil would be very difficult, if not impossible, without pulling the head."
"This works for the right front and left rear broken exhaust manifold bolt."
"Put on as preventive measure due to past experience with the poor GM design."
Repair exhaust leaks with Dorman's Exhaust Manifold to Cylinder Head Repair Clamp. Eliminates the need to remove cylinder head, saving you time and money.
Reviews
Find Best Price at Amazon"If removing the head is not an option then you'll have to either live with the leak or get one of these."
"Actually do work if you dont have the time to remove broken bolt."
"5 stars for amazon taking it back."
"Worked on my 2007 chevy tahoe, 5.3l flex fuel."
"Installed on 2003 Silverado 4.8 left front, and it works great."
"Worked awesome on the front drivers side very easy straight forward install."
"Good luck on that driver side."
"Easy fix for a common problem.... had a broken header bolt that was to deep to weld and it tried walking sideways while drilling it.... this product made for a quick an easy fix."
More like a complete kit than a single part, many of Dorman's Exhaust Manifolds include gaskets and hardware for a complete installation. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"I recommend not using the supplied gasket."
"Just as described fit was perfect good product."
"Fit perfectly."
"Works great no problems so far."
"Manifold cracked and will need replacing after less than 20.000 miles."
"junk , had to reorder 2 last one close enough to make work."
Best Automotive Replacement Exhaust Studs & Nuts
Brand New Cylinder Head To Exhaust Manifold Stud & Nut Set (1-Side). Commonly Needed For Normal Wear & Tear & Breaking From Rust/Corrosion. Fits 1992-2011 4.6L 5.4L 6.0L 6.8L Ford Lincoln Mercury Navistar Engines. View The Vehicle Compatibility Chart To Verify Your Specific Model. Includes 10 Grade 8 Carbon Steel Studs & 10 Nuts. Replaces N811313-S431, W701706-S2, W703902-S403. Specs: Thread = M8-1.25; Length = 56mm. Used To Attach The Exhaust Manifold To Cyliunder Head on Ford 4.6L 5.4L 6.0L 6.8L Engines.
Reviews
Find Best Price at Amazon"These worked out perfectly for my 06’ Ford F-150 5.4l."
"worked great on my 04 f250 5.4."
"Amazing company to work with."
"Delivered sooner than expected ."
"It was obviously put in the envelope torn open, you couldn't miss the gaping hole."
Best Automotive Replacement Exhaust Bolt & Spring Kits
Dorman’s Engine Intake Manifold Isolator Bolts are suitable for a range of Ford applications. Enter your model number to make sure this fits.
Reviews
Find Best Price at Amazon"With two intake plenum isolator bolts broken, and after staring at the product picture and description for a couple of hours, I took a chance and ordered."
"They are specified for use in the Windstar on many sites and even on Amazon it states they will not fit the Taurus (see picture)."
"Changed my intake manifold gaskets and swapped these in the place of the beat up OEM ones in my 2003 f150 4.2l."
"If you have to change your manifold gaskets, make sure you change the MANIFOLD Isolator bolts, they will reseal around your fuel plenum."
"use these for intake ford explorer v6 4.0 better then hex !"
"Great replacement bolts for one of FORD's finest invention of the plastic plenum on top of the intake."
"Excellent factory replacement for my 2004 Ford F-150 Heritage 4.2L V6."
"It came with extra pieces i didnt need but im just a beginner mechanic and i was not going to deep into the repair for the extra pieces."