Best Special Application Pullers
The OTC 8150 is designed to fit Pitman arms on domestic cars and light trucks. Designed to fit Pitman arms on domestic cars and light trucks.
Reviews
Find Best Price at Amazon"A ton of maintenance items need to be performed (AC overhaul, Power Steering, Rear Main Seal, Electrical issues, and a little body work) but are well within my abilities. I soaked the thing in PB Blaster, hit the sides and the puller bolt with a 3lb sledge, applied heat, and only managed to bend the 2 pullers rented from Autozone and Advance Auto. I removed it from the standard, "No Frills", packaging and applied some synthetic grease to the threads just to ensure everything would go smoothly."
"The Mercedes pitman is on really tightly and takes some real tension to get it to remove. Method I used was to tighten the tension on the puller and then tap the pitman with a small hammer."
"Don't get me wrong, it was still a PITA to get the pitman arm off, but I never would have gotten it off if it were not for this tool."
"I had to use a breaker bar initially, but just as i thought the threads on this thing had stripped, Much to my surprise, the pitman arm just fell off."
"I tried using a pickle fork, a "3 pronged" traditional puller, a hammer, penetrating oil, and heat to try and remove the large pitman arm from my early saginaw power steering box."
"I bought this puller after doing tons of research on which one would be best for pulling the pitman arm on my 2005 Dodge Ram 2500. The main thing with forcing bolt style puller is to keep the threads lubricated."
"If you need to get a pitman arm off this is the real deal.Do,nt even mess around with those two arm pullers and hope that it does not snap the arms off.This puller is nice and heavy and THICK just make sure you lube the jack forcing screw with good chassis grease because its going to get HOT this weakens the forcing screw threads and strip out happens.no more cheap pullers to buy now that I have this BAD BOY!"
Instructions: Suit for dent size (within 14cm). Hot Glue Sticks+ Glue Gun+ Glue Tabs +Bridge Dent Puller Sets. 1.Clean damage surface with a damp clean cloth. 2.put the glue to gun and heat(also it need about 5-10min ). 3.pull the trigger and apply the drawing gasket with extruded glue (The 4 holes of gasket should be applied with hot melt glue). 4.immediately place pad in the center of the dent and hold until sticks. 5.place stem of pad through hole pulling bridge and screw knob. 6.tighten knob until pad pops off. 7.clean the surface. New Design - Unique polygon bridge design and 5pcs high quality glue tabs for more easy repair damage.
Reviews
Find Best Price at Amazon"Because panel had a paper backing was not able to completely pull dent."
"i just want to use one word to describe this production: amazing!!!"
"I felt weird about applying hot glue direct to my paint."
"bought this tool for my hubby， he told me it takes a while to get used to fixing the car and dent by the using it。anyway， it is a not expensive tool，so don't expect it can make you car will look a new car again。."
"Removed the dent of my car."
"Very good design,my car accidentally hit by others, not serious, but the impact of appearance, to repair the line charges too expensive, with this can be easily repaired, save a lot of money."
"Feel so good when they told me they should save thousands of dollar to spend on car body repair shops, that’s really good experience."
"The most important is that it saved me a lot of money and helped me spend a enjoyable time with my wife."
Instructions: Suit for dent size (within 14cm). Hot Glue Sticks+ Glue Gun+ Glue Tabs +Bridge Dent Puller Sets. 1.Clean damage surface with a damp clean cloth. 2.put the glue to gun and heat(also it need about 5-10min ). 3.pull the trigger and apply the drawing gasket with extruded glue (The 4 holes of gasket should be applied with hot melt glue). 4.immediately place pad in the center of the dent and hold until sticks. 5.place stem of pad through hole pulling bridge and screw knob. 6.tighten knob until pad pops off. 7.clean the surface. This is the professional dent and ding repair kits,it can help you repair it by yourself.
Reviews
Find Best Price at Amazon"Because panel had a paper backing was not able to completely pull dent."
"i just want to use one word to describe this production: amazing!!!"
"I felt weird about applying hot glue direct to my paint."
"bought this tool for my hubby， he told me it takes a while to get used to fixing the car and dent by the using it。anyway， it is a not expensive tool，so don't expect it can make you car will look a new car again。."
"Removed the dent of my car."
"Very good design,my car accidentally hit by others, not serious, but the impact of appearance, to repair the line charges too expensive, with this can be easily repaired, save a lot of money."
"Feel so good when they told me they should save thousands of dollar to spend on car body repair shops, that’s really good experience."
"The most important is that it saved me a lot of money and helped me spend a enjoyable time with my wife."
Best Bearing Pullers
The "Pilot Bearing Pulling Attachment" allows you to remove pilot bearings, thrust washers and smaller bearings hidden in a shaft or housing. Jaw spread cover ranges from 5/8 inch to 1 inch.
Reviews
Find Best Price at Amazon"Although it has a rather large "female" fitting to attach it to a "slide-hammer"; I solved the problem by going to my local vendor of "nuts & bolts" and buying the correct size of bolt to fit the "female" fitting."
"The jaws are too big for 4-cyl engine (smaller transmission input shaft diameters) applications, but it has worked fine on V6/V8 larger transmission jobs."
"Wow..."
"Worked perfectly on my 98 mustang gt pilot bearing."
"looks well made but too large for a .550 dia."
"Had to make an adapter to fit my small slide puller with a 1/2 shaft."
"Also used it to pull an input shaft seals out of a transmission."
Best Steering Wheel Pullers
This harmonic balancer removal tool blow molded case keeps puller kit neat and tidy. Shankly’s crankshaft pulley puller features an assortment of bolts making this tool versatile for a range of jobs. VERSATILE TOOL: Designed to handle a range of jobs, a gear puller, pulley puller, flywheel puller and more, providing the user multiple uses for one tool set.
Reviews
Find Best Price at Amazon"When we got it, the label on it only says harmonic balancer and was a bit confused as we were used to steering wheel removers to have hoods grasp on to the wheel."
"5 star rating is on appearance only as I have not used the tool yet."
"Just got today and put straight to work i used it to pull a flywheel on a Kohler K series engine worked great."
"Did the trick."
"Haven't had to use but happy to own."
"This worked great pulling the steering wheel from my Solara Convertible."
"works great."
"Great product."
Best Jaw Pullers
Tiger Tool heavy-duty universal joint puller is engineered for use with up to a one-inch impact wrench, this tool provides the ultimate "brute strength" for disassembling drivelines. Does not damage the driveshaft, yokes, joints, or bearing cups and is tested and recommended by the Driveshaft Division of Dana Corporation.
Reviews
Find Best Price at Amazon"This thing is the mule of pulling u joints on class 8 trucks."
"Very good, and the shipping arrived in time."
"GREAT PRODUCT AND A MUST HAVE TOOL IN A HEAVY TRUCK SHOP."
"Made the work super easy and easy to use."
"Excellent service, fantastic product, money maker/saver."
"best u joint puller out there."
"Works great."
Best Puller Sets
The OTC 9-way slide hammer puller set pulls flange-type rear axles and most front-wheel drive hubs and the internal and external jaws provide a variety of combinations to pull bearings, gears and seals. Includes a grip wrench adapter and a dent puller attachment for sheet metal or other unique pulling requirements.
Reviews
Find Best Price at Amazon"This was Ideal for what I needed, Had a stubborn wheel bearing and worked our great."
"Well made quality product."
"This presses out the bearing and allows you to press in the new bearing without ever removing the steering knuckle form the car."
"This is one fantastic tool !"
"This was purchased to use in an automotive shop."
"Nice set......fixed my broken front wheel lug studs the right way on my 08 Honda odyssey after One of the big tire chain shops ran them on with an impact gun instead of using a torque wrench like an experienced tech would."
"great set, worked perfect for pulling the hub assembly off my wifes van."
"Pretty nice kit, well built."